In February 2027, a battery sold into Europe starts needing a record of its own life. Article 77 of the EU Batteries Regulation is direct about it: “From 18 February 2027 each LMT battery, each industrial battery with a capacity greater than 2 kWh and each electric vehicle battery placed on the market or put into service shall have an electronic record (‘battery passport’).”
Most commentary on the battery passport is written for car makers and cell manufacturers. It reads differently if you build machines. A lithium pack in a floor scrubber, an aerial platform or a materials handling machine is exactly the kind of battery the rule reaches, and the passport is not a label you print once. It has to carry information about how that specific battery has been used.
Key Takeaways
- From 18 February 2027, industrial batteries over 2 kWh placed on the EU market need a battery passport, alongside LMT and electric vehicle batteries.
- The regulation defines an industrial battery broadly, including any battery over 5 kg that is not an EV, LMT or SLI battery, which reaches most equipment traction packs.
- The passport must hold information resulting from the battery’s use, including cycles, negative events, temperature and state of charge, and it must be kept accurate and up to date.
- That makes it an in-service data obligation, not a documentation exercise, and it falls on whoever places the battery on the market.
The Definition Is Wider Than Most People Assume
The regulation’s definition is worth reading in full, because it is what brings equipment into scope. An industrial battery is “a battery that is specifically designed for industrial uses, intended for industrial uses after having been subject to preparation for repurposing or repurposing, or any other battery that weighs more than 5 kg and that is neither an electric vehicle battery, an LMT battery, nor an SLI battery.”
That final clause does most of the work. Very few traction batteries in industrial equipment weigh under 5 kg, and the regulation defines an electric vehicle battery by reference to type-approved road vehicle categories, which most industrial machines are not.
Then comes the passport threshold of 2 kWh. Many battery-powered industrial machines sit comfortably above it. Whether a specific product is in scope is a question for your compliance team, but a manufacturer shipping lithium-powered equipment into Europe should assume the question applies until it is answered.
A Passport That Has to Be Kept Current
The part that turns this from paperwork into an engineering problem is what the passport must contain.
Article 77 says it holds information about the battery model and “information specific to the individual battery, including resulting from the use of that battery.” Annex XIII then spells that out: “information and data resulting from its use, including the number of charging and discharging cycles and negative events, such as accidents, as well as periodically recorded information on the operating environmental conditions, including temperature, and on the state of charge.”
And the responsibility is explicit. “The economic operator placing the battery on the market shall ensure that the information in the battery passport is accurate, complete and up to date.”
Cycle counts, temperature history and state of charge are not things anyone can write down at the factory. They accumulate in service, on a battery that may be in a customer’s building in another country, and they have to be reflected in a record that stays accurate.
Who Is Actually Responsible
The regulation places the obligation on “the economic operator placing the battery on the market.” For an equipment manufacturer, whether that is you or your battery supplier depends on how the battery reaches the market: fitted inside your machine, sold as a replacement, or supplied separately.
This is not a question to settle by assumption. It changes who needs the data, who needs to be able to update the record and who carries the liability if it is wrong. The regulation does allow an operator to give written authorisation for another party to act on its behalf, which is how many manufacturers will end up sharing the work with their battery suppliers.
What does not change is the underlying requirement. Somebody has to hold an up-to-date record of each battery’s use, and the only reliable source for that is the battery and the machine it sits in.
The Record Follows the Battery Through Its Life
The passport is designed to outlast the machine’s first owner, and in some cases the machine itself.
Where a battery is repurposed or remanufactured, the regulation requires it to “have a new battery passport linked to the battery passport or passports of the original battery or batteries.” The passport only ends when the battery is recycled: it “shall cease to exist after the battery has been recycled.”
The purpose behind the use data is stated too. The criteria for deciding who may access the more detailed information include “the necessity of having such information in order to evaluate the status and residual value of the battery and its capability for further use.” In plain terms, the record exists so that the next person can judge what the battery is worth and what it can still do.
For equipment manufacturers that is a familiar idea in a new place. It is the same question a buyer of used equipment asks about the machine, now written into law for the battery inside it.
Built on Open, Portable Data
One requirement deserves attention from anyone choosing a platform. Article 77 requires that the information be “based on open standards and be in an interoperable format, transferable through an open interoperable data exchange network without vendor lock-in, machine-readable, structured and searchable.”
The phrase “without vendor lock-in” appears in the regulation itself. A battery record that can only be read inside one supplier’s proprietary system is not what the law describes. For a manufacturer, that argues for capturing battery use data in a form the business controls and can export, rather than depending on a closed portal from whoever made the cells.
What to Do Before February 2027
Establish which of your products carry batteries in scope, by weight, chemistry, use and capacity. Decide who is the economic operator for each route to market, and put the answer in writing with your battery suppliers. Identify how cycle counts, temperature, state of charge and negative events will be captured from batteries already in service, not only on the bench. And check that the data will be portable in the form the regulation requires.
The battery management system usually records much of this internally. The gap for most manufacturers is not measurement but reach: getting that information out of a machine in the field and into a record that stays current. Battery behaviour as an operational signal is covered separately in how runtime, battery and location data improve asset management.
Where ARMOR™ Fits
ARMOR™ has roots in exactly this kind of equipment. The company grew out of commercial floor machine service, and it works with battery-powered machines including lithium systems. ARMOR 4+™ wires into the machine’s electrical system and reports voltage, current and runtime hours into ARMOR Asset Central™, continuously and from the field.
That is the reach problem the passport creates. Electrical behaviour and usage are captured from the machine while it works, and held in a record the manufacturer controls and can share with suppliers, dealers and owners.
ARMOR™ does not produce a battery passport and does not make a product compliant with the Batteries Regulation. The passport has its own content, format and access rules. What ARMOR™ provides is a live route to in-service data from machines already shipped, which is the part most manufacturers do not yet have. How it is built in at the production stage is described on the ARMOR™ for Equipment Manufacturers page.
Frequently Asked Questions
Does this apply to lead-acid batteries as well as lithium?
The passport threshold is framed around battery category and capacity rather than chemistry, so a large industrial lead-acid battery is not automatically outside it. Check the specific requirements for each product with your compliance team rather than assuming chemistry decides the question.
We sell only in North America. Should we care?
Only if your products, or the batteries in them, reach the EU market, including through distributors or customers who export. As with other EU product rules, the obligation follows the product rather than the manufacturer’s address.
Can the battery management system handle this on its own?
The BMS usually measures much of what the passport needs. What it cannot do alone is get that information off the machine and into a current, accessible record, which is the part that requires connectivity.
What happens to the passport when a machine is sold second-hand?
The passport stays with the battery, and a repurposed or remanufactured battery gets a new passport linked to the original. That continuity is the point: the record is meant to help the next owner judge the battery’s condition and value.
See how ARMOR™ is built into equipment like yours, at the build stage. ARMOR™ for Equipment Manufacturers